Zdjęcie w tle

SUQ-MADIQ

Autorytet
  • 691wpisów
  • 1005komentarzy

@kreyg Klawiaturze? Luksus... Ja w "Prince of Persia" gralem na podrobionej pseudo-konsoli do gier, kupionej na bazarze.

Zaloguj się aby komentować

@SUQ-MADIQ poradnik z cyklu "Management for dumbs" zamiast "dummies" - takie nawiązanie do poradników z Tag i MS WIN z lat 90.

@ql00 to nie brednie tylko oczywista rzeczywistość lat 90 i wczesnych 00. Roboty nie było, a januszom się w dupach przewracało ze szczęścia. Oby te czasy już nigdy nie wróciły.

Zaloguj się aby komentować

#zeglarstwo #esp32 #poradnikarmatora - taki tag do zczarnolistowania kto nie jest zainteresowany biedackimi rozwiązaniami diy do użycia w jachcie


In this episode we set up a ESP32-E Firebeetle 2 to be able to monitor key data from my Yanmar 3GM30 (and applicable to any engine). The device will run a program based on SensESP from the Signal K team and interface with my Openplotter system on my boat Raspberry Pi. This system could be easily extended to be NMEA 2000 for integration into an existing NMEA 2000 marine electronics system.


The data that the device will provide is as follows:


• Oil Pressure - requires a pressure sender and a port on the engine to connect to.


• RPM - requires a pulse from the spinning engine, this is usually the 'W' terminal or Tachometer Signal wire. This could also be done using a flywheel sensor or something similar


• Fuel Burn Rate - this will be calculated from the RPM


• Temperature Sensors - I am using 1-Wire sensors for the following:


○ Oil Temperature


○ Aft Cabin Temperature


○ Exhaust Elbow Temperature


○ Exhaust Barrel Temperature


○ Alternator Temperature


• Environmental Sensor - this device will report Temperature, Relative Humidity and Air Pressure in the engine bay


https://youtu.be/Zay2ALtgxzc

@SUQ-MADIQ wydaje mi się że z silnika za pomocą CAN byś mógł wyciągnąć dane bezpośrednio bez konieczności używania tylu sensorów

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

@SUQ-MADIQ jesteś jedną z osób jaka mnie motywuje do rzucenia tego stylu życia, jest ciężko ale widzę różnicę i wiem że warto.

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

Zaloguj się aby komentować

#zeglarstwo #bezpieczenstwonamorzu


AIS as a SURVEILLANCE TOOL


An Automatic Identification System (AIS) is an automated tracking system that displays other vessels or vessels in the vicinity.


SOLAS Requirements


The IMO Convention for the Safety Of Life At Sea (SOLAS) Regulation V/19.2.4 requires all vessels of 300 GT and above engaged on international voyages and all passenger ships, irrespective of size, to carry AIS onboard.


What will appear on the Screen of your AIS


Vessels Info


-MMSI number


-IMO number


-Name and Call Sign


-Length and Beam


-Type of ship


-Ship’s position with accuracy indication


-Position timestamp (in UTC)


-Course Over Ground (COG)


-Speed Over the Ground


-Heading


-Bearing


- Range 


-Ship’s draught


-Type of cargo


-Destination and ETA


Facts about AIS 


How does the AIS system work?


AIS works by taking the vessel’s location and movements through its GPS or the internal sensors built into the AIS unit. It is fitted on ships for the identification of ships and navigational marks. However, it is only an aid to navigation and should not be used for collision avoidance.


The AIS onboard must be switched on at all times unless the Master deems that it must be turned off for security reasons or anything else.


Your ship also shows on the screens of other vessels in the vicinity, provided your vessel is fitted with AIS. If AIS is not fitted or not switched on, there is no exchange of information on ships via AIS.


TWO TYPES OF AIS


Class A: Mandated for all vessels 300 GT and above engaged on international voyages as well as all passenger ships.


Class B: Provides limited functionality and is intended for non-SOLAS vessels. Primarily used for vessels such as pleasure crafts.


AIS operates principally on two dedicated frequencies or VHF channels:


AIS 1: Works on 161.975 MHz- Channel 87B (Simplex, for the ship to ship)


AIS 2: 162.025 MHz- Channel 88B (Duplex for the ship to shore)


AIS AS A SURVEILLANCE TOOL


In coastal waters, shoreside authorities may establish automated AIS stations to monitor the movement of vessels through the area.


Coast stations can also use the AIS channels for shore to ship transmissions and to send information on tides, NTMs and located weather conditions.


To sum it up, the AIS only improves the safety of navigation by assisting the OOW/VTS.

81594728-8dea-4e78-abf1-12c1803ec11f

Zaloguj się aby komentować

Zaloguj się aby komentować